Abstract
The workers villages are typical residential type during Shanghai’s urbanization built from the 1950s to the 1980s. Due to changes in the urban environment and climatic circumstances, the workers villages have inadequate natural ventilation and difficulty in dispersing pollutants, putting residents’ health at risk. In the context of urban renewal, it is necessary to clarify the effect of building morphological indicators on pedestrian level wind, especially in such old residential communities. In this paper, 100 workers villages representatives were gathered by GIS. Their summer ventilation conditions were simulated using the CFD solving the LES turbulence equation. The correlation between 9 morphological indicators and 2 pedestrian level wind indicators was obtained quantitatively by Pearson analysis and regression analysis. The result shows increasing the building coverage of 0.94% in the workers villages, the ratio of the area of the static wind in summer will increase subsequently by 10%. The results highlight the importance of considering morphological indicators to enhance the wind environment, and provide suggestions for the environmental transformation of communities with similar characteristic in the high-density city.
You have full access to this open access chapter, Download conference paper PDF
Similar content being viewed by others
Keywords
1 Introduction
The rising density and height of buildings within cities, along with the rapid development of urbanization, has had an impact on the original natural climate. The concentrated expansion of urban centers in coastal parts of China has exhibited a high degree of saturation, and dense building clusters in cities can decrease air flow and have a direct impact on urban wind speed [1]. Excessive wind speed and inadequate ventilation can both cause changes in the thermal environment, which can impair human comfort in outdoor settings and population health [2]. Uneven wind speed distribution also contributes to the accumulation of dangerous gases and air pollutants like sulfur dioxide [3], as well as major air pollution concerns like haze, which can cause respiratory ailments and reduce daily visibility [4].
Because of the dense population of Shanghai’s core city, convective winds are severely impeded, and significant sections of the building complex are windless [5]. Due to changes in construction requirements and changes in the surrounding environment, which is poorly ventilated and prone to heat and pollutant buildup, some old neighborhoods built in the last century have wind speeds of less than 1 m/s in parts of the interior of residential areas, causing problems for pedestrians. By the end of 2011, the existing workers villages in Shanghai had a total housing area of around 170 million square meters, accounting for 31% of the total area [6]. Workers villages have also been an important objective of Shanghai’s urban renewal plan, which is focusing on urban regeneration and traditional old district renovation. In order to mitigate the heat island effect and promote sustainable urban growth, the rehabilitation of ventilation conditions in old neighborhoods in high-density cities has become a critical issue.
The goal of this research is to improve the outdoor wind environment in old communities, which are represented by the workers villages. Building coverage and height, for example, have been demonstrated to have a considerable impact on regional ventilation performance in studies [7], which will affect to some extent the comfort and safety of wind environment in outdoor pedestrian spaces [8]. The outdoor wind environment of the old communities represented by the workers villages are studied, quantitative indexes are introduced, and the relationship between building form and outdoor wind environment is presented qualitatively and quantitatively through the calculation of an idealized geometric form model and multiple regression analysis, and applied to the optimization of existing buildings.
2 Methodology
In the present study, a total of 100 neighborhood models of workers villages in different regions of Shanghai were collected via GIS and Rhino. The morphological indicators of the neighborhood models were calculated by the plug-in Grasshopper. Then, wind environment simulation of 100 workers villages and their surroundings were calculated, and the data obtained were filtered and processed by the plugin ladybug and eddy3D. It is an interactive interface on rhino/grasshopper platform based on openFOAM open source computational fluid dynamics (CFD) library. Solving LES equation has the advantages of fast and accurate. It has been proved to be adaptive in complex urban environment [9]. Eventually, correlation analysis and regression analysis were carried out between morphological and environmental factors to eliminate loosely related factors and clarify their correlations. Scatter diagrams were also created to verify the correlation. The overall process is shown in Fig. 1.
2.1 Geography and Climate of the Research Object
The rapid urbanization process is currently a big issue all over the planet. With such a large population, there is a great demand for natural resources, which stimulates city development at a high density. The high-density built-up area in Shanghai causes the wind speed to drop year after year, reducing the comfort of pedestrian wind environments [10]. The workers villages were constructed earlier, and the wind environment was not taken into account during building, resulting in poor overall comfort.
In this study, about 100 existing old workers villages in Shanghai were selected as samples. The models were obtained and processed through software such as ArcGIS and Rhino to obtain a model library of the research objects.
2.2 Morphological Indicators
Eight morphological indicators were used in the study to quantitatively describe the varied spatial characteristics of workers villages: building coverage ratio, building volume density, floor area ratio, average building height, roughness length, height dispersion, frontal area index, and sky view factor.
Among these eight morphological indicators, the significant impact of average building height has been proven in numerical experiments [11], and its increment led to larger air change rates at roof and targeted canyon monotonously [12]. A study took place in Hong Kong [13] emphasis that frontal area index is to be a better morphological factor in depicting the wind environment at the pedestrian level. Illustration and equation of various indicators are showed in Fig. 2 and Table 1. Each indicator’s abbreviations are included in the table and will be used later in the text.
2.3 Pedestrian Level Wind Indicators
In consideration of the characteristics of wind environment in the community, the geographical features of its location in high-density urban areas, where wind speeds greater than five meters rarely occur, and comfort under different pedestrian behavior, this paper puts forward an approximate division threshold for Shanghai workers villages. Static wind area is classified as areas where wind speed is smaller than 1 m/s, and areas with wind in 1–5 m/s and >5 m/s are defined as comfort wind area and strong wind area relatively. The area ratio of static wind area is used to describe the proportion of uncomfortable pedestrian areas in the community in the total area, especially in summer.
Other than static wind ratio, this paper also uses standard deviation to express the overall dispersion degree of each calculation point of wind speed in the whole test model site. Due to the construction of high density, the uniformity of air flow will be affected. The lower the wind speed dispersion, the more stable the overall wind speed distribution and the weaker the wind turbulence, resulting in a better wind environment. The unreasonable layout of building corners and building spacing will lead to a sudden increase in wind speed, leading to higher wind speed dispersion, resulting in unsafe or comfortable circumstances. Equation of various indicators are shown in Table 2.
2.4 Pearson Correlation Coefficient and Linear Regression
Pearson correlation coefficient is used to expose the correlation of indicators, whose output range from −1 to 1, and 0 means no correlation. Negative value means negative correlation and positive value means positive correlation. The larger the value to both sides, the stronger the correlation is. Pearson correlation coefficient’s capability of achieving this is accomplished through centralization and cosine calculation.
Furthermore, linear regression explains the higher correlation and is able to generate the results of linear regression equation. Correlation analysis is the basis and premise of regression analysis, and regression analysis is the deepening and continuation of correlation analysis. Due to the existence of some samples with wide orders of magnitude, directly processing ignores some independent variables with extremely small value level may cause an inaccurate fitting result, normalization is introduced to avoid dimensional effects. Normal distribution of data is kept and zoomed to the range of 0 to 1.
3 Results and Analysis
After completing the wind environment simulation of 100 real models, this paper firstly makes a qualitative description of the overall and individual workers villages, along with description of data distribution, and then makes a quantitative analysis using Pearson correlation and linear regression.
3.1 Geographical Distribution and Analysis of Individual Cases
Figure 3 shows the geographical distribution of selected models, which display a circular distribution centered on urban area. It is obvious that most of the tested workers villages in Shanghai don’t display an optimistic performance in comfortable wind area––in the figure, a large number of points is biased to orange and red.
The static wind ratio of the 3 areas (Fig. 4), on a mesoscale, is different from the overall condition. Lighter colored points are gathered in Area B than A and C, also showing the characteristics of homogenization, which means it has a better pedestrian level wind environment than area A and C in summer. Different geographical locations, preliminarily assumed, will alter specific morphological aspects, hence influencing the wind environment. Specifically, three areas have a varied overall tendency in terms of construction orientation. A and C are oriented primarily southeast, whereas B is oriented north–south. Besides, FAI and other morphological indicators will be affected by different orientations, which alter the wind environment. As the satellite image display, BD of surrounding sites of area B (Fig. 3b) is lower than which of the other plots (Fig. 3a, c), indicating that the overall building density of the two plots B is also much lower than that of the other plots.
Some preliminary conclusions can also be obtained from the micro scale. In addition to the variances in morphological aspects induced by different geographical locations, the layout of workers villages has an impact on the wind environment. The determinant dominates most workers villages, although there are other combinations of determinant and point group or enclosed organization. Because the point group and determinant combination in area B (Fig. 4b) is more extensive, the area of static wind is comparatively small. As a result, it is clear that this arrangement is worthy of note and can be used as a component in the optimization and reconstruction of future workers villages.
3.2 Descriptive Analysis of Data
The morphological characteristics, BCR, and SVF have a more concentrated distribution with fewer outliers, as seen in Fig. 5. BVD, \({z}_{0}\), σ, and FAR are all right skewed, with more outliers. The distribution of static wind area ratio is more concentrated than the distribution of wind speed standard deviation among the environmental performance indexes, and the distribution of wind speed standard deviation is more scattered.
From the box-and Whisker plot for all indicator result distribution of wind simulated models (Fig. 5), it can be seen that the median of the static wind area ratio of the workers villages is about 0.87, and the vast majority of the values fall between 0.6 and 1, which means that the vast majority of the workers villages’ summer static wind area ratios is above 60%. Thus the overall wind environment of Shanghai workers villages is unsatisfactory.
3.3 The Correlation Between Spatial Morphology and Wind Environment
Comprehensive scatterplots, data distribution of every indicator and relevant calculated Pearson correlation coefficient are shown in a matrix visualization (Fig. 6). In the matrix, the darker red the color is, the higher the positive correlation between the two indicators is explained, while the darker blue the color is, the higher the negative correlation between the two indicators is explained, corresponding correlation coefficients are also marked, and the range of which is 0–1. Through comprehensive analysis, it can be preliminarily determined that: (1) Within environmental indicators, Static wind ratio strongly correlated to wind deviation. (2) Between environmental and morphological indicators, i. Site area size strongly correlated to deviation, following a linear negative correlation. ii. BCR, BVD, FAR weakly correlated to static wind ratio, and all present positive correlation. iii. FAI and wind deviation show slight correlation, following a positive correlation. iv. z0 and deviation show weak correlation, following a positive correlation.
To further obtain quantitative relationships between morphological and environmental indicators, linear regression is conveyed. Based on its result, Fig. 7 shows the correlation and significance (P value) of coefficients. In general, the results are as follows: (1) Unfortunately, all data have a low degree of fitting. It illustrates that the real model’s wind environment is more complex, as a result of numerous elements acting together, and that the link with specific morphological markers is weak. (2) Wind speed standard deviation and site area size show the highest regression coefficient among all indicators, which is close to 0.3 (Fig. 7a) and respond great significance (P < 0.0001) It remains to be explored why the site size is negatively related to wind-speed standard deviation. (3) Relatively speaking, BCR indicates higher correlation than other morphological indicators, but merely does it explain the regression relationship between the two indicators so far.
The regression analysis shows that increasing the building coverage of 0.94% in the workers villages, the ratio of the area of the static wind zone in summer will increase subsequently by 10%, with a site area of 1.4–18.1 hectares, a building volume density of 1.97–9.97, and an average building height of 8.9 to 39.6 m. In the workers villages with a site area of 1.4–18.1 hectares, a building volume density of 1.97–9,97, and an average building height of 8.9 to 39.6 m, the building site area is reduced by about 1.5 m2 and the summer wind speed dispersion increases by 10%.
4 Conclusions
In this study, numerical simulations were used to analyze the wind environment and verify the influencing factors for 100 workers villages neighborhoods in Shanghai. Correlation analysis and regression analysis of wind environment indicators are conducted. The following findings provide researchers and planners with a deeper understanding of pedestrian level wind conditions in residential areas in Shanghai and similar climatic regions.
(1) The correlation analysis reveals that, among the morphological indicators, building coverage, building volume density and volume ratio correlate more significantly with the area ratio of the static wind zone. This conclusion may also be superimposed by multiple indicators. (2) Frontal area index, building coverage ratio, building volume density and floor area ratio are the four morphological indicators which affect the outdoor wind environment of Shanghai workers villages. These indicators can be used for urban renewal and renovation of old neighborhoods. (3) It can be seen that there is a correlation between morphological indicators and environmental indicators, but they don’t have a high enough fitting precision. The main reason is conjectured to be the presence of more anomalies in the data analysis that affect the degree of fit. Furthermore, the measured data are based on real world model, which adds more uncertainties compared with idealized models.
In the subsequent study, more dimensions of environmental data such as wind speed ratio may be added and correlation analysis may be conducted. In addition, this study mainly uses linear regression equation to analyze the correlation between the indicators, but the correlation between wind environment and building morphology cannot be described by a simple linear equation. The N-S equation is a two-linear nonlinear equation, and should also be explored and analyzed in conjunction with the k-s turbulence model, etc. For further research, we hope to use black-box operation through machine learning to fit morphological and environmental indicators more intelligently and effectively, and better find the correlation between the data.
References
Yang Y, Gou A (2021) Research on wind environment simulation of commercial district based on Phoenics—taking shanghai central building group as an example. In IOP conference series: earth and environmental science (Vol 647, No 1, p 012193). IOP Publishing
Ng E, Cheng V (2012) Urban human thermal comfort in hot and humid Hong Kong. Energy Build 55:51–65
Tominaga Y, Stathopoulos T (2013) CFD simulation of near-field pollutant dispersion in the urban environment: a review of current modeling techniques. Atmos Environ 79:716–730
Ing-hui M, Zhuo-cheng M, Zhong-qi Y, Yuan-hao Q, Fu-hai G, Jian-ming X, Min C (2016) Analysis of the temporal and spatial distribution of haze and its influencing factors in Shanghai. Polish J Environ Studies 25(5)
Yang Y, Gou A (2021) Research on wind environment simulation of commercial district based on Phoenics—taking Shanghai central building group as an example. In: IOP conference series: earth and environmental science (Vol 647, No 1, p 012193). IOP Publishing
Peng Z, Jia L, Li L, Quan SJ, Yang PPJ (2017) How the roofing morphology and housing form affect energy performance of Shanghai’s workers village in urban regeneration. Energy Procedia 142:3075–3082
Palusci O, Monti P, Cecere C, Montazeri H, Blocken B (2022) Impact of morphological parameters on urban ventilation in compact cities: the case of the Tuscolano-Don Bosco district in Rome. Sci Total Environ 807:150490
Yang F, Qian F, Lau SS (2013) Urban form and density as indicators for summertime outdoor ventilation potential: a case study on high-rise housing in Shanghai. Build Environ 70:122–137
Zheng X, Yang J (2021) CFD simulations of wind flow and pollutant dispersion in a street canyon with traffic flow: comparison between RANS and LES. Sustain Cities Soc 75:103307
Du Y, Mak CM, Tang BS (2018) Effects of building height and porosity on pedestrian level wind comfort in a high-density urban built environment. In: Building simulation (Vol 11, No 6, pp 1215–1228). Tsinghua University Press
Coceal O, Belcher SE (2005) Mean winds through an inhomogeneous urban canopy. Bound-Layer Meteorol 115(1):47–68
Chen G, Rong L, Zhang G (2021) Impacts of urban geometry on outdoor ventilation within idealized building arrays under unsteady diurnal cycles in summer. Build Environ 206:108344
Wong MS, Nichol JE, To PH, Wang J (2010) A simple method for designation of urban ventilation corridors and its application to urban heat island analysis. Build Environ 45(8):1880–1889
Xu Y, Ren C, Ma P, Ho J, Wang W, Lau KKL, ... Ng E (2017) Urban morphology detection and computation for urban climate research. Landscape Urban Plann 167:212–224
Shi Y, Xie X, Fung JCH, Ng E (2018) Identifying critical building morphological design factors of street-level air pollution dispersion in high-density built environment using mobile monitoring. Build Environ 128:248–259
Ma T, Chen T (2020) Classification and pedestrian-level wind environment assessment among Tianjin’s residential area based on numerical simulation. Urban Climate 34:100702
Tian J, Xu S (2021) A morphology-based evaluation on block-scale solar potential for residential area in central China. Sol Energy 221:332–347
Macdonald RW, Griffiths RF, Hall DJ (1998) An improved method for the estimation of surface roughness of obstacle arrays. Atmos Environ 32(11):1857–1864
Gál T, Unger J (2009) Detection of ventilation paths using high-resolution roughness parameter mapping in a large urban area. Build Environ 44(1):198–206
Jiang D, Jiang W, Liu H, Sun J (2008) Systematic influence of different building spacing, height and layout on mean wind and turbulent characteristics within and over urban building arrays. Wind Struct 11(4):275–290
Shi Y, Lau KKL, Ng E (2017) Incorporating wind availability into land use regression modelling of air quality in mountainous high-density urban environment. Environ Res 157:17–29
Mittal H, Sharma A, Gairola A (2018) A review on the study of urban wind at the pedestrian level around buildings. J Build Eng 18:154–163
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Open Access This chapter is licensed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license and indicate if changes were made.
The images or other third party material in this chapter are included in the chapter's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the chapter's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
Copyright information
© 2023 The Author(s)
About this paper
Cite this paper
Zhang, X., Wu, X., Yang, L., Xu, J., Luo, R., Yao, J. (2023). Effect of Morphological Indicators on the Pedestrian Level Wind of the Existing Workers Villages in Shanghai. In: Yuan, P.F., Chai, H., Yan, C., Li, K., Sun, T. (eds) Hybrid Intelligence. CDRF 2022. Computational Design and Robotic Fabrication. Springer, Singapore. https://doi.org/10.1007/978-981-19-8637-6_15
Download citation
DOI: https://doi.org/10.1007/978-981-19-8637-6_15
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-19-8636-9
Online ISBN: 978-981-19-8637-6
eBook Packages: Intelligent Technologies and RoboticsIntelligent Technologies and Robotics (R0)